Baltic Brown Granite Effect Kit KITCHEN TOP in epoxy resin

• The 2.49 kg kit (1.66 + 0.83) covers 1 square meter (+ 10 g Sahara rose gold pigment + 10 g Sahara bronze pigment + 25 ml black dye + 99.9% Isopropyl)
• The 4.15 kg kit (2*1.66 + 0.83) covers 2 square meters (+ 10 g Sahara rose gold pigment + 2*10 g Sahara bronze pigment + 25 ml black dye +2* Isopropyl 99, 9%)
• The 8.33 kg kit covers 4 square meters (+ 2*10 g Sahara rose gold pigment + 4*10 g Sahara bronze pigment + 5*25 ml black dye + 99.9% Isopropyl)
• The 16.66 kg kit covers 8 square meters (+ 4*10 g Sahara rose gold pigment + 8*10 g Sahara bronze pigment + 10*25 ml black dye + 99.9% Isopropyl)

Kit Contents:

• 2.49 kg, 4.15 kg, 8.33 kg or 16.66 kg of Art Coat Epoxy “Art Pro” for a high quality base
• Black dye from the “Colorfun” line for the perfect stone shades
• Metallica Sahara pink gold and bronze pigment for that extra touch of sparkle
• To enhance the appeal of the design:  99.9% Isopropyl

It is strongly recommended to add:

• To make the coating last longer: Polishield 100 Gloss (additional option, not included in the price). 100 gr copre 1 M2 + 11.99 eur / 500 gr copre 4 M2 + 34.99 eur)

Each kit includes dyes and pigment in sufficient quantity for the amount of resin required.

Quick Guide Instructions:

Step N1: Primer 

Start by carefully measuring the amount needed to cover the surface based on the consumption of 150 g/m2, making sure to follow the proportions indicated to obtain a homogeneous mixture. Once the base has been prepared, proceed with adding the dye, choosing between white or black depending on your needs. The quantity of colourant to add to the mixture can be measured in a few drops (max 5% by volume). This step is crucial to achieve the desired colour and ensure uniformity of the application.

Before applying the primer, it is essential that the surface intended for treatment is adequately prepared. Sand the surface with a coarse grit (40 or 60) before any operation. Make sure it’s completely clean, using a soft cloth or brush to remove any pigment, dirt or debris. The surface must also be completely dry; residual humidity can compromise the adhesion of the primer and its effectiveness in sealing the surface.

Once the surface is ready, apply the mixture evenly, using a suitable tool such as a brush, roller or spatula, depending on the size of the area to be treated and your personal preference. The key is to get a thin, even layer that can cover the entire area without leaving gaps or excessive product buildup..

After application, it is essential to allow the primer to dry completely before proceeding with further  reatments or finishes on the surface. The recommended waiting time is 12 hours; this range may vary slightly depending on environmental conditions, such as humidity and temperature, but offers a good compromise to ensure the mixture has time to dry and adhere properly. During this period, avoid touching or stressing the treated surface to ensure optimal results. Don’t worry if you notice any discrepancies on the surface, the next main pour will level everything perfectly.

Step N2: application 

Start by applying masking tape around the perimeter of your countertop to contain the epoxy you’re about to pour. This step is essential to ensure the resin stays where it is needed. After applying the resin, wait about 1.5 hours before gently removing the tape. To ensure coverage is even and complete, plan to use approximately 1.6kg of resin for every square meter of surface area.

When you are ready to mix the resin, use a drill equipped with a paddle mixer for quick and even action (use at low speed), taking about 2 minutes for this operation. If you prefer to mix by hand, be prepared to take double the time. Don’t forget to scrape the sides and bottom of the container halfway through the process with a stick to ensure all the material is mixed well. Subsequently, separate the already mixed resin into different glasses, allocating approximately 85% of the weight to the black colour, dividing the remaining 15% into three containers. Add the colors Oxide Red, Gold and Rich Gold by mixing them separately with the resin in the individual glasses until you obtain an intense and uniform colour.

You will now have four containers: one black (85% of the mass), one Di Rosso Oxide, one Gold and one Rich Gold: they will be your tools to create your marble effect.

Pour the black resin onto the surface; In this way we are creating a surface on which we will then apply the different colours to obtain the shades of the marble veins. To remove trapped air bubbles, gently run a propane torch or heat gun over the surface.

Wait about 10/15 minutes before creating the veins, the resin will thicken slightly creating an even more realistic effect.

Pour the three coloured resins in drops, overlapping them in some areas, creating the veins you like best. For a more nuanced effect you can work on the grain with a spatula, slightly and delicately blending the edges of the grain.

To create a realistic effect, once the coloured resins have been applied, spray the supplied isopropyl alcohol on the surface: this step will further improve the Granite effect

It is very important that the density of the resin is correct: the Art Pro was designed for this type of application but always check that it is of the right density; in fact, environmental conditions are a detail that cannot be predicted, it is the applicator who has the situation in hand.

Once the adhesive tapes have been removed, approximately 1.5 hours after application, if there are any dry edges, moisten them slightly by wearing a protective glove to promote an even appearance. Use appropriate tools, such as spatulas or plastic scrapers, to spread and level the resin along the edges, making sure to cover the entire area well. After letting the resin cure for 24 hours, you can apply a clear top coat or PoliShield scratch-resistant paint to further protect the surface.

Remember that when you remove the tape, it is essential that the resin is partially hardened, neither too liquid nor completely solid, to avoid unwanted drips.